2001년부터 산업용 부품 및 엔지니어링 솔루션.
독일에서 전 세계로 빠른 배송
다양한 결제 방법다양한 결제 옵션
Rickmeier R45/160 FL-Z-DB16-W-SAE2.1/2-R-P Gear Pump
| 브랜드 | |
| 카테고리 | 펌프 |
| 제품명 | Rickmeier R45/160 FL-Z-DB16-W-SAE2.1/2-R-P Gear Pump |
| 제품 코드 | R45/160 FL-Z-DB16-W-SAE2.1/2-R-P |
저희에게 연락하세요! 영업일 기준 24시간 이내(주말 및 공휴일 제외) 재고 상태와 예상 납기를 안내해 드립니다.
제품 설명
Rickmeier의 Rickmeier R45/160 FL-Z-DB16-W-SAE2.1/2-R-P Gear Pump을(를) 포함한 제품은 병행 수입 채널을 통해 조달되며 United States의 고객에게 신속하고 안정적으로 배송됩니다. Imtek Engineering은 경쟁력 있는 가격으로 정품 Rickmeier 부품을 제공합니다. Rickmeier R45/160 FL-Z-DB16-W-SAE2.1/2-R-P Gear Pump이 당사 웹사이트에 등록되어 있지 않더라도 언제든지 견적을 요청하실 수 있으며, 담당 팀이 신속히 답변 드릴 것입니다.
United States8 Technical data The technical data in this catalogue are intended for general information. During installation, operation and maintenance, the operating instructions and the information specified on the products
must be observed.
8.1 Operational limits The maximum permissible operating conditions for gear pumps in the standard version are described in the following. Contact RICKMEIER whenever it is necessary to exceed these specifications. In such cases, please contact our Sales department.
As a prerequisite for a long service life and maximum operational safety, the flow medium must retains its lubricity and, if possible, be clean and non-corrosive, but in any case must always be free
of hard admixtures.
Consideration must be given also to the following:
Properties Flow medium
Inlet pressure (constant pressure according to
DIN 24312)
Kinematic viscosity Degree of contamination (according to ISO 4406:1999, max.)
Gas content (undissolved, max.) Temperature (NBR seals) Temperature (FKM seals)
Radial shaft seal, standstill 4) Radial shaft seal during operation 4) Mechanical seal
Magnetic coupling
Min.
5 mm2/s 1)
-25 °C -25 °C -0.4 bar 5) -0.4 bar 5) -0.4 bar 5) -0.4 bar 5)
Max.
20000 mm2/s 1) 21/19/17 10 vol. % 2) 80 °C 150°C 3) 5 bar 0.5 bar 6) 10 bar 7)
16 bar 7)
Tab. 8: Operational limits of the standard design 1)
Depending on the application and operating conditions, lower and/or higher viscosities are possible, please
contact us.
2) Undissolved gas in the flow medium leads to increased noise emissions.
3) If used above 120°C, special measures may be required under certain circumstances (e.g., heat-resistant
clutch, pressure relief valve with heat-resistant spring, etc.); with optionally available sealing materials, different temperature ranges can be implemented.
4) Manometric 5) For speeds up to 1500 rpm, up to -0.5 bar permissible; in the short term: -0.6 bar (e.g., during start-up)
6) With optionally available radial shaft seal up to 6 bar 7) Versions for higher pressures available on request
22 / 52
TB3-NNNN-111 • 01
must be observed.
8.1 Operational limits The maximum permissible operating conditions for gear pumps in the standard version are described in the following. Contact RICKMEIER whenever it is necessary to exceed these specifications. In such cases, please contact our Sales department.
As a prerequisite for a long service life and maximum operational safety, the flow medium must retains its lubricity and, if possible, be clean and non-corrosive, but in any case must always be free
of hard admixtures.
Consideration must be given also to the following:
Properties Flow medium
Inlet pressure (constant pressure according to
DIN 24312)
Kinematic viscosity Degree of contamination (according to ISO 4406:1999, max.)
Gas content (undissolved, max.) Temperature (NBR seals) Temperature (FKM seals)
Radial shaft seal, standstill 4) Radial shaft seal during operation 4) Mechanical seal
Magnetic coupling
Min.
5 mm2/s 1)
-25 °C -25 °C -0.4 bar 5) -0.4 bar 5) -0.4 bar 5) -0.4 bar 5)
Max.
20000 mm2/s 1) 21/19/17 10 vol. % 2) 80 °C 150°C 3) 5 bar 0.5 bar 6) 10 bar 7)
16 bar 7)
Tab. 8: Operational limits of the standard design 1)
Depending on the application and operating conditions, lower and/or higher viscosities are possible, please
contact us.
2) Undissolved gas in the flow medium leads to increased noise emissions.
3) If used above 120°C, special measures may be required under certain circumstances (e.g., heat-resistant
clutch, pressure relief valve with heat-resistant spring, etc.); with optionally available sealing materials, different temperature ranges can be implemented.
4) Manometric 5) For speeds up to 1500 rpm, up to -0.5 bar permissible; in the short term: -0.6 bar (e.g., during start-up)
6) With optionally available radial shaft seal up to 6 bar 7) Versions for higher pressures available on request
22 / 52
TB3-NNNN-111 • 01
자주 묻는 질문
Rickmeier의 Rickmeier R45/160 FL-Z-DB16-W-SAE2.1/2-R-P Gear Pump에 관한 자주 묻는 질문입니다. Imtek Engineering은 United States에서 Rickmeier의 Rickmeier R45/160 FL-Z-DB16-W-SAE2.1/2-R-P Gear Pump를 조달하는 데 도움을 드릴 준비가 되어 있습니다.
Imtek Engineering은 신뢰할 수 있는 공급 채널을 통해 정품 Rickmeier 제품을 조달하여 United States 고객에게 경쟁력 있는 가격으로 제공합니다.
